For interface housings with female connector, for mating with a male connector, on Backplane (BP).
For interface housings with female connector, to attach on the connecting pins of a female connector. Installation in the wiring field of the subrack.
Secures PCB without front panels.
Secures PCB’s without front panels. Used for easy locking and ejecting of PCB’s
This PCB cover protect the soldered side against dirt and contact. Two versions are available: A standard PCB cover and a PCB cover for use with a coding strip. The coding strip PCB cover can be used in connection with a coding strip on the connector.
This PCB cover protect the soldered side against dirt and contact. Two versions are available: A standard PCB cover and a PCB cover for use with a coding strip. The coding strip PCB cover can be used in connection with a coding strip on the connector.
PCB cover for coding strip 6U This PCB cover protect the soldered side against dirt and contact. Two versions are available: A standard PCB cover and a PCB cover for use with a coding strip. The coding strip PCB cover can be used in connection with a coding strip on the connector.
This PCB cover protect the soldered side against dirt and contact. Two versions are available: A standard PCB cover and a PCB cover for use with a coding strip. The coding strip PCB cover can be used in connection with a coding strip on the connector.
Partition Wall For partitioning of a subrack part. The partition wall 6 U can also be used as a RFI shielded subrack divider in 6 U and 2x3 U parts.
Mounting Rail B tapped M 2.5 For mounting connectors in accordance to IEC 60 603/ DIN 41 612. For mounting at the rear profile on subracks type alpha with insulating strip and insulating bushings. For mounting at the rear profile on subracks type delta. Material: aluminum Finish: blank
For connector styles F 48, C96, H11, H15, and F24/H7.
For connectors styles E 48 and E 160.
With integrated coding, for connector styles F 48, H15 and F24/H7 The Metal interface housings RFI 20 standard are not supplied with RFI springs.
Metal Interface Housings RFI 20 COD With integrated coding, for connector styles F 48, H15 and F24/H7 width(hp) 4
For locking of PCB‘s witout front panels. The locking rail is mounted at the horizontal rail in front of the PCB‘s. A labeling strip can be insert into a groove.
This hinged labelling rail is mounted on the subrack flanges. Normally it is placed in front of the front panels. For ejecting a PCB, the rail is turned down.
Self adhesive. For identifiying PCB slots in the subrack. The PCB slot number can be read thru the hole in the front panel. Note: The label strip cannot be read while using the RFI spring P2. Material: PC/PE foil Color: yellow/black
The dust- and hose-proof small casing InterShell IP allows customized electronic applications with following attributes.- custom specific adjustments
- quick ans und uncomplicated installation
- appropriate for:
- table-top housing for measuring and testing systems
- small case for customized applications
- mobile enclosures for external using
- protection class IP 65
- individual colour design.
The flexible aluminium housings for small form factors are characterised by following properties:- customized adjustments
- quick and uncomplicated mounting
- appropriate for packaging of small electronic units like
- - euroboards
- - customized electronic
- - mITX Boards.
- protection up to IP67
- a wide range of colours for a finish
- additionally printing as customer requirements are possible
Your advantages- Shock and vibration resistant
- Water and dustproof
- Optimal HF-tightness
The InterMeZo housing from Intermas is a modular and cost effective housing solution for high quality industrial electronics in a visually attractive design, developed for the highest possible flexibility and simplest possible assembly, with expansion capabilities for more deman ding needs, compliant with stringent EMI/ESD protection specifications, and with extensive configuration options to fulfil application specific requirements. Versions The InterMeZo housings are available to assembly 19” or metric subracks. Alternatively, any dimensions for variable applications are possible.
The InterLock desktop housing has been designed to cover subracks. Also System-Module can be dressed up. The special design features of the InterLock desktop housing:- The covering elements are formed from recyclable polystyrene plate-material warmly and the joints are welded together by means of a chlorine carbon solution coldly.
- Material strength of 4 to 10 mm can be processed according to demand of the device.
- Easy assembly or disassembly of the case shells. Both case shells are locked by a clamp groove without screws.
- The case is upgradeable by feet and handles.
- However, on account of an economic manufacturing technology special dimensions or special colors can be also already realised for small quantities at a reasonable price.
- Extensive range of accessories is available.
Description The special design features of the InterCase desktop housing:- A desktop housing with a simple design for standardized plugin units and individual assemblies.
- The easy to access design allows all covering parts to be removed at any time.
- The bottom cover and the rear panel are provided with louvers.
- The side plates include perforations for attaching profile rails at different board depths.
- The comprehensive range of Intermas subrack accessories allows individual configuration of the desktop housing.
- Can be RFI-shielded.
Insulating Strip For insulated mounting of wiring supports, e. g. of the mounting rail B. Mounted between horizontal rail and wiring support.
Ident-plate 4 HP The ident-plate is markable and printable. Snapped in after mounting the handle at the front panel. Material: aluminum Finish: silver silk matt anodized
Ident Plate for handle FP. The ident plate is markable and printable, snapped in after mounting the handle to the front panel.
20 HP for horizontal mounting of 6 U PCB‘s in 3 U subracks. The horizontal mounting frame needs 52 HP in the width. For 84 HP subracks are available Placed right: 52 HP for horizontal mounting frame, 32 HP for 3 U PCB‘s Placed left: 52 HP for horizontal mounting frame, 1 HP for air and leakage paths, 31 HP for 3 U PCB‘s.
Hinged Front Panel 85 HP With slits in the side edges for insertion of RFI springs. The hinge is screwed to the profiled rail of the subrack. An 84 HP threaded strip is needed. To be used in combination with below mentioned flanges only. Finish: front side anodized, rear side conductive Delivery: 1 front panel 1 hinge 3 grounding bushings Mounting parts Delivery: as unassembled kit. Assembled kits on request.
Handle FP Assembled with M 2.5 screws and with 1 additional self tapping screw from 6 HP. The handle is held against torsion by means of two nipples.
Material: aluminum Finish: anodized
Guide component F with integrated front panel for mounting of a 3 HP metal interface housing RFI in a 3 U subrack..
Guide component F for mounting of a 3 HP metal interface housing RFI in the upper or lower area of 6 U subracks.gers.
Guide component F for mounting of a 3 HP metal interface housing in any position of the mounting area.
For interface housings with female or male connector, for mating di rectly to the PCB (LP) connector. Installation in the wiring field of the subrack.
Front Profile VE1 (also rear profile by using of a front panel on the rear). Material: aluminum Finish: anodized
For assembly on a PCB. Handle and front connector are screwed on the front panel. The plain front panel is easy to modify. Four versions are available: 1. Flat front panel blank The front side is covered with a removable transparent foil. 2. Flat front panel anodized Front anodized, rear conductive. 3. Flat front panel RFI Front anodized, rear conductive. With slits in the side edges for insertion of RFI springs. 4. Extruded front panel RFI Made of extruded aluminum alloy, with slits in the side edges for insertion of RFI springs for contact. Surface finish is colorless chromated.
Front Panels with Ejector Handle For easy release of PCB’s with high pin connections. The ejector handle is extends through the front panel and is screwed together with the bearing bushing at the front connector. Four versions are available: 1. Flat front panel blank. The front side is covered with a removable transparent foil. 2. Flat front panel anodized. Front anodized, rear conductive. 3. Flat front panel RFI Front anodized, rear conductive. With slits in the side edges for insertion of RFI springs. 4. Extruded front panel RFI Made of extruded aluminum alloy, with slits in the side edges for insertion of RFI springs for contact. Surface finish is colorless chromated.
Front Panels with IEEE Handle For easy pull of PCB’s with high density connectors accordance specification IEEE 1101.10. The assambled handle kit is stuck in the milled space of the front panel and is secured with a clamped spring. Afterwards the PCB are screwed on the intergrated front connector. Two versions with IEEE handle are available: 1. Flat front panel RFI Front anodized, rear conductive. With slits in the side edges for insertion of RFI springs. 2. Extruded front panel RFI Made of extruded aluminum alloy, with slits in the side edges for insertion of RFI springs or for contacting. Surface finish is colorless chromated.
Flange without Nose This flange can be mounted at various depth on the side panel grid. Material: aluminum, extruded Finish: anodized
This flange is suitable for mounting of a continous front panel of 85 HP and a hinged front panel of 85 HP in a subrack. The flange will be mounted to the side panel by means of the mounting screws for the horizontal rails. Material: aluminum, extruded Finish: colorless chromated
Flange for Wall Mounting For mounting of a subrack on a wall. Material: aluminum Finish: blank, seawater resistant
The flange can be mounted to the side panel by means of the mounting screws for the horizontal rails. Material: aluminum, extruded Finish: anodized
Feet Kit: 2 feet with tip-up 2 feet without tip-up 4 self-tapping screws Material: Ultramid Purchase Online: 409-059-640-Q10 Feet Kit Package
Ejector Handle The ejector handle extends through the front panel and is screwed together with the bearing bushing at the front connector.
The special design features of the DiVar housing:- It consists of profiles into which aluminum, sheet steel, stainless steel or plastic panels with a thickness of 1.5 to 2.5 mm are inserted and, if desired, secured with screws. A wall panel at the rear and a panel at the front are screwed to the profiles.
- The flexible design allows variable configuration of the housing geometry in all three axes, this allowing adaptation of the housing to customer specific requirements.
- Different surfaces can be selected for an individual appearance.
- The proven RFI contact spring concept ensures optimum RFI shielding.
- Rails with threaded holes can be pressed into the profile grooves, for example to screw in PCBs or mounting plates.
- The extensive range of Intermas accessories allows unrestricted configuration and installation of both standardized and non-standard components.
Quick Overview DiVar Desktop Housing with keyboard area Delivery 4 profiles 4 cover plates 2 side plates Assembly hardware
DiVar Desktop Housing with keyboard area Delivery 4 profiles 4 cover plates 2 side plates Assembly hardware
Overview Hole diameter 4 / 5.2 x 4 mm. The cover plate will be mounted with self tapping counter sunk screws outside of the side panels. Additionally the cover plate is secured to the horizontal rails by clips. Material: aluminum, 1 mm thick Finish: blank, seawater resistant- Quick Overview Hole diameter 4 / 5.2 x 4 mm. The cover plate is mounted with self tapping counter sunk screws on the inside of the side panels. Additionally the cover plate is secured to the horizontal rails by clips. Material: aluminum, 1 mm thick Finish: colorless chromated, seawater resistant
Quick Overview Hole diameter 8.0 mm. The cover plate is mounted with self tapping counter sunk screws at the side panels and at the horizontal rails. Material: aluminum, 1 mm thick Finish: blank, seawater resistant
